 
VISION (Home Theatre)
Star earthed with
6 individually filtered outlets
and additional high frequency filter for AV systems
Includes
free power cable
VISION
in silver
£595.00 in
silver free P&P
£635.00 in Black free P&P
To buy online click
here www.highendcable.co.uk
Overview
The GII Mini Sub & Vision are IsoTek's top of the range filter
based component from component isolating mains power distributor.
It was designed to be a very rewarding single box ‘plug-n-play’
solution for a complete audio or home theatre system. The GII Mini
Sub & Vision offer astounding value for money and gives a taste
of what our truly high-end solutions offer. Within our product range
the GII Mini Sub & Vision sit between the Solus and isolation
transformer based SubStation.
At
the rear of the unit you will note six high quality outlets, these
are individually filtered to stop components ‘talking’
to each other or corrupting the clean supply provided by the unit.
This is achieved by a series of delta filters on the outputs and
a sophisticated filter circuit, which was inspired by work in cryogenics,
and harnesses the technique used for the switching of cryogenic
coils. Both products feature our new ‘Polaris-X’ technology
that draws mains contaminants away from audio components plugged
into the unit.
Outputs
1 & 2 have been given a higher power rating and should be used
for high current devices, for example power amplifiers, integrated
amplifiers, some ‘tube’ pre-amplifiers, projectors and
plasma screens etc. The remaining four are suitable for all other
equipment, for example CD players, turntables etc…
GII Mini Sub & Vision features enhanced protection through stabilising
the units voltage and giving it a very large absorption ability,
this is extremely important in today’s society where dangerous
power surges can damage sensitive audio equipment.
All
fusing is external, this eliminates any need to enter the product.
The unit is so safe that even if the mains are wired incorrectly
in the rest of the house or environment that the product is used,
the unit will correct the problem sonically.
All
components are of the highest grade and are under stressed, this
gives greater longevity. These are hand soldered onto a PCB with
silver solder, the large PCB also features a ground plane upper
surface acting as a very high grade common mode filter across the
whole board, this allows the unit to act as a true faraday cage,
protecting itself from RFI and other components from the job it
performs.
Safety
In the interests of safety the unit should be placed upon its own
dedicated shelf on an audio grade equipment rack. The unit may be
placed on top of or under other pieces of equipment, do not exceed
a maximum weight loading of 20kg.
Areas
where ‘tube’ amplifiers are present should not exceed
25 degrees. If you are positioning the Mini Sub or Vision in the
close proximity of such a device please be aware of this factor.
If
you have to locate the unit on the floor we strongly recommend you
do not place the unit near heat sources, such as radiators or air
ducts. Good air circulation is essential to prevent heat build up
within the chassis. Do not place the Mini Sub or Vision on a soft
surface, for example a rug or carpet, which could block the ventilation
intakes on the underside of the unit. Do not let any liquids spill
onto or objects fall into the chassis. Should either of these events
happen immediately switch off the unit at the wall socket, wait
for at least one minute, unplug all other cables and return it to
your authorised IsoTek dealer for a full service.
Placement
Ideally the unit should be placed upon its own dedicated shelf of
an audio grade equipment rack. If this is not possible the unit
may be placed on top of or under other pieces of equipment to a
maximum weight limit of 20kg. Due to the products careful screening
by way of a large ground plan within the unit, no adverse effects
should be caused by this placement. If you have to locate the unit
on the floor or in any other location please refer to the safety
section of this manual.
Equipment
coupling
Once the Mini Sub or Vision is placed connect the unit to a mains
wall socket, we recommend that a good quality cable is used and
that the wall socket is also unswitched. Turn off all equipment
you wish to have a clean mains supply, unplug the cables relating
to these from the wall socket or redundant distribution block you
may have been using and plug these into the rear sockets of the
Mini Sub or Vision. Outputs 1 & 2 (marked with a red dot) have
been given a higher power rating and should be used for high current
devices, for example power amplifiers, integrated amplifiers, projectors
and plasma screens etc. The remaining four are suitable for all
other equipment.
System
integration
We strongly recommend that a good quality mains cable is used and
this cable is consistent throughout your system. Look for a cable
with good conductors, for example oxygen free copper, this cable
should also have a high degree of shielding from RFI.
Specifications
The following information relates only to the IsoTek Mini Sub GII
and Vision. These are original products and should not be confused
with previous or ‘copy cat’ models.
Number
of outlets: 6
Type of outlets: 13A UK unswitched
Standard mains inlet: IEC fused
Mains voltage: 190 - 260VAC
Maximum current
(outlets 1 & 2): 10 Amps
Maximum current
(outlets 3 to 6): 6.3 Amps
Total maximum current: 16.3 Amps
External mains fuse: 6.3 Amps (13Amps UK)
Dimensions: 444mm x 85mm x 305mm (WxHxD)
Weight (boxed): 7.0Kg
|
